ProStart CT-3371 Guide d'installation télécharger pdf (Page 4)

Quick installation Guide http://www.prostart.org P.7

 Parking brake shutdown circuit (for manual vehicles only). With the vehicle running under remote

start, disengage the parking brake. The engine should shut down immediately. If the engine continues

to run, check the parking brake switch connection.

 OEM alarm control. Make sure the module is able to arm and disarm the OEM alarm (if applicable).

 Door locks and trunk testing. Make sure each of these options respond to the transmitter (if

installed).

 Door pin shutdown circuit (for manual vehicles only). Make sure the system exits ready mode

when each door is opened. (Test each door.)

 Starter kill option. Sit inside the vehicle with all doors closed. Arm the vehicle, then try to start the

engine with the key. The engine should not start. If the engine starts, rewire the starter kill to reach

proper operation.

 Valet mode. Make sure the remote car starter is able to properly enter and exit valet mode. When

setting the remote car starter into valet mode, pressing the lock button will lock the doors without

activating the starter kill. (Refer to the user guide for further information on valet mode.)

 Idle mode. Make sure the vehicle properly enters and exits idle mode.

 Door. Make sure that when the system is armed, opening any door or opening the trunk will trigger

the alarm (if installed).

 Hood trigger. Make sure that when the system is armed, opening the hood should trigger the alarm.

 Most comebacks are the result of misunderstandings about how a product works or performs.

Take the time to properly explain all functions and features to the customers before they leave

the premises. Doing this will save time and money.

DIAGNOSTICS – PARKING LIGHT FLASH TABLE

Diagnostic table for start failure.

Parking lights flashes Cause

(Manual transmission only)

x Ready mode is not activated.

1 slow

2 quick

x The system is set to valet mode.

(Automatic transmission only)

x The parking brake is active.

x Yellow loop is connected.

x Brake wire is active.

(Manual transmission only)

x Tach signal is not learned.

x A tach signal is detected before Ignition.

x Hood wire is active.

Diagnostic table for shutdown.

Parking lights flashes Cause

x Runtime has expired.

x Shutdown by remote.

x Ready mode is activated.

x Failed start (VTS or tach failure, depending on selected).

x Brake shutdown.

x Hood shutdown.

Flash for 30 sec.

x Panic mode.

Note: The installer can also use the PRG-1000 to diagnose shutdown and remote start failures.

Refer to the PRG-1000 manual guide.

P.4 http://www.prostart.org Quick Installation Guide

OPTION 2 Active arming

OPTION 3 Passive arming (3 min.)

FUNCTION 4 – Door lock / unlock pulse timing

OPTION 1* 7/10-sec. lock / unlock pulses

OPTION 2 4-sec. lock / unlock pulses

OPTION 3 7/10-sec. lock pulse and two ¼ -sec. unlock pulses

FUNCTION 5 – LED flashing

OPTION 1* ENABLED (will only flash when ignition is OFF)

OPTION 2 DISABLED

OPTION 3 ENABLED (will only flash when Starter kill engages [depends on Mode 1,

Function 3 programming])

MODE 2

* INDICATES DEFAULT SETTING

FUNCTION 1 – Engine Run Time

OPTION 1 Run time = 3 minutes in gas mode / 8 minutes diesel mode

OPTION 2* Run time = 15 minutes in gas mode / 20 minutes diesel mode

OPTION 3 Run time = 25 minutes in gas mode / 30 minutes diesel mode

FUNCTION 2 –Idle Mode & Turbo Mode (auto) / Turbo Mode (manual)

OPTION 1 Idle mode & turbo mode DISABLED (AUTO) / turbo mode DISABLED (MANUAL)

OPTION 2* Idle mode & turbo mode ENABLED (AUTO) / turbo mode DISABLED (MANUAL)

OPTION 3 Idle mode & turbo mode ENABLED (AUTO) / turbo mode ENABLED (MANUAL)

FUNCTION 3 – Engine type and Cold Weather Mode

OPTION 1 Diesel mode with 20-minute run time in cold weather mode (30-sec. wait to start delay)

OPTION 2* Gas mode with 3-minute run time in cold weather mode

OPTION 3 Diesel mode with 8-minute run time in cold weather mode (18-sec. wait to start delay)

FUNCTION 4 – AUX 1 programming

OPTION 1 Horn confirmation on 2

press of LOCK button

OPTION 2* Priority door access

OPTION 3 Horn confirmation when pressing LOCK button

FUNCTION 5 – SmartStart™

OPTION 1 SmartStart™ ON

OPTION 2* SmartStart™ OFF

MODE 3

* INDICATES DEFAULT SETTING

FUNCTION 1 – Ready Mode Option / Hybrid Option

OPTION 1 ENABLED by handbrake

OPTION 2* ENABLED by remote

OPTION 3 Hybrid option ENABLED

FUNCTION 2 – Bypass

OPTION 1 ADS

OPTION 2* Xpresskit

OPTION 3 Fortin

FUNCTION 3 – Bypass Type / Push to start

OPTION 1 One-Way communication / Push to Start DISABLED

OPTION 2* Two-Way communication / Push to Start DISABLED (For Xpresskit only)

OPTION 3 Two-Way communication / Push to Start ENABLED (For Xpresskit only)

OPTION 4 One-Way communication / Push to Start ENABLED

HORN ADJUSTMENT

Note: Before adjustment, horn option must be enabled.

1. In programming mode (page 3).

2. Press and hold the brake pedal, then simultaneously press the UNLOCK and START/STOP buttons 

the horn will chirp 5 times.

3. Release the brake pedal.

4. To change the timing:

1. To increase the horn pulse by 3 ms, press the LOCK button.

2. To decrease the pulse by 3 ms, press the UNLOCK button.

3. To increase the pulse by 10 ms, press the START/STOP button.

4. To decrease the pulse by 10 ms, press the TRUNK button.

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

ProStart CT-3371 Guide d'installation Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Les démarreurs à distance ProStart CT-3371