ProStart CT-5072 Guide d'installation télécharger pdf

ONE-WAY AUTOMATIC/MANUAL TRANSMISSION

REMOTE STARTER WITH FULL ALARM SYSTEM

AND VIRTUAL TACH SYSTEM (AS PRG-1000

COMPATIBLE)

Notice

The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be

that either damage to the vehicle itself or to the unit. This unit must be installed by a certified technician using all safety devices

supplied. Please note that this guide has been written for properly trained Autostart technicians: a certain level of skills and

knowledge is therefore assumed. Please review the installation guide carefully before beginning any work.

Warning

Before installing the unit, if installing on a vehicle with a manual transmission, test that the OEM Door Switch contacts of the

vehicle work well, and that the Parking Brake system operates properly. If installing on a vehicle with an automatic

transmission, test that the vehicle does not start when the gearshift lever is in the “Drive” position. If it starts in gear, reset the

remote starter to manual transmission.

QUICK INSTALLATION GUIDE

TableofContents

Manual or Automatic Transmission setup 1

Entering Programming Mode 2

Programming the transmitter to the module 2

Entering Programming Options 2

Programming Options 3

Horn / Siren adjustment 4

Setting up the TACH 4

Virtual Tach adjustment 4

Multi-speed Tach Programming (if installed) 5

Resetting the Module 5

Bypass 5

NEW FEATURE – SmartStart™ 5

Testing 5

Troubleshooting 7

Diagnostics – Parking Light Flash Table 7

Diagnostic table for start failure. 7

Diagnostic table for shutdown. 7

The wiring diagram is at the middle of this guide.

MANUAL OR AUTOMATIC TRANSMISSION SETUP

This module may be installed on vehicles with manual or automatic transmissions. It is originally configured for

manual transmissions. If the vehicle you are working on is automatic, it is mandatory to make a few quick and

easy modifications before the unit is connected. In the event that the configuration requires changes afterwards,

a complete reset (page 5) will be necessary before those changes become effective.

To install this unit in a vehicle with a MANUAL transmission:

1. Make sure the Yellow loop on the PC board is connected (default).

2. Connect the Orange handbrake wire, located on the 12-pin harness, to the vehicle handbrake circuit (-).

3. Connect the Blue/White (+) OR Grey (-) door input wire, located on the 12-pin harness, to the vehicle

door pin wire which monitors all the doors of the vehicle (only use 1 of the 2 door trigger inputs).

4. Make sure the Purple TACH wire is wired to a tach source – the TACH wire MUST be hooked up when

the module is set for a manual transmission.

5. Make all your regular connections.

6. Power up the unit by first inserting the 5-pin connector, then the 6-pin connector and finally the 12-pin

connector. The parking lights will flash 4 times.

7. When learning the transmitter, the parking lights will flash 5 times quickly.

8. Upon the first successful remote start, the system will lock the transmission settings to manual mode.

To install this unit in a vehicle with an AUTOMATIC transmission:

1. Cut the Yellow loop on the PC board (Yellow wire).

2. Make sure the Orange handbrake wire is not connected to any of the vehicle circuits (cut and tape).

3. Make all the regular connections.

4. Power up the unit by first inserting the 5-pin connector, then the 6-pin connector and finally the 12-pin

connector. The parking lights will flash 4 times.

5. When learning the first transmitter, the parking lights will flash 5 times quickly then give 2 slow flashes.

6. Upon the first successful remote start (once the yellow loop has been cut), the system will lock the

transmission settings to automatic mode.

Note: If upon pressing the START/STOP button the parking lights give 3 slow flashes, make sure that the

Orange handbrake wire is not connected, the hand brake is not engaged and that the yellow loop is cut and

isolated/taped.

1 2 3 4 5 6

Résumé du contenu

Page 1 - QUICK INSTALLATION GUIDE

ONE-WAY AUTOMATIC/MANUAL TRANSMISSION REMOTE STARTER WITH FULL ALARM SYSTEM AND VIRTUAL TACH SYSTEM (AS PRG-1000 COMPATIBLE)Notice The manufacturer wi

Page 2 - ENTERING PROGRAMMING OPTIONS

P.2 http://www.autostart.ca Quick Installation Guide ENTERING PROGRAMMING MODE These are the programming buttons: Complete step by step programming1

Page 3 - PROGRAMMING OPTIONS

Quick installation Guide http://www.autostart.ca P.3 x LOCK to access mode 1; x UNLOCK to access mode 2; x TRUNK to access mode 3;x START/STOP to a

Page 4 - SETTING UP THE TACH

Quick installation Guide http://www.autostart.ca P.7  Shock and warn-away trigger. Make sure that the shock works well and is not too sensitive so

Page 5 - NEW FEATURE – SMARTSTART™

Quick installation Guide http://www.autostart.ca P.5 OPTIONAL TIME DELAY ADJUSTMENT IN VIRTUAL TACH SYSTEM Follow these steps to program crank time

Page 6 - WIRING SCHEMATIC

V2.01 SS - Sept. 7, 2011 -TAd: HIGHTACH Threshold: NORMALProgrammingAssistance Button(P.A.B.)1. Grey/Blue...(-) N/A2. White/Purple...(-) Horn

Plus de documents pour Les démarreurs à distance ProStart CT-5072

Voir le document ProStart CT-5072 Guide d'installation

ProStart CT-5072 Guide d'installation (2 pages)

Voir le document ProStart CT-5072 Guide de l'utilisateur

ProStart CT-5072 Guide de l'utilisateur (14 pages)

ProStart CT-5072 Guide d'installation (30 pages)

Commentaires sur ces manuels

Pas de commentaire

ProStart CT-5072 Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Les démarreurs à distance ProStart CT-5072. ProStart CT-5072 Installation guide Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Les démarreurs à distance ProStart CT-5072

Commentaires sur ces manuels

Produits connexes et manuels pour Les démarreurs à distance ProStart CT-5072